Bill Hewlett 200A Oscillator Prototype as shown in the MEASURE "Wrapping it up" issue Courtesy of Hewlett Packard Company

Before the First

At the origin of the story is this audio oscillator built by Bill Hewlett for his Stanford University thesis project in 1938.

It is a resistance tuned oscillator covering from 35 cps (frequency unit was the cycle at this time) to 35,000 cps in 3 ranges. The major problem with such a resistor / capacitor tuned Bridge is to obtain a constant level output over a full decade frequency range. Bill Hewlett solved the problem by inserting a non-linear element in the feedback loop of the oscillator. This element controls the amount of feedback in accordance with the amplitude of oscillation and consequently maintains the proper operating point in the system. And what makes the idea a genius one is that the non-linear element is nothing else than a simple 3 Watts light bulb.

The HP 200B first HP Product Oldest Showpiece of the Kenneth Kuhn Collection Courtesy of Professor Kenneth Kuhn

The First HP Commercial Products

Bill's prototype became the HP company's first product the HP 200A.

As shown in the wiring diagram below, two options with different frequency ranges were available: the 200A and 200B. A small modification of 6 resistors values resulted in different frequency ranges 35 to 35,000 cps for the 200A and 20 to 20,000 cps for the 200B.

All other specifications are common for the two units. A two-stage power amplifier with transformer-coupled output delivers 1 Watt into a 500 ohm resistance load. The output voltage is controlled ahead of the output amplifier from a front panel level control. The total harmonic distortion is lower than 0.5 %.

The HP 200B with rounded corners shown in this photo comes from the Kenneth Kuhn collection. Units with this particular case style are very rare today. This unit was manufactured in 1941, probably at the Polly and Jake's location and may have been handled by Bill and Dave themselves.

Professor Kenneth Kuhn of the University of Alabama Birmingham is the owner and curator of one of the world's largest collections of HP original early instruments. Almost every instrument produced by Hewlett Packard during the first 20 years can be seen on his Web Site at : http://www.kennethkuhn.com/hpmuseum - Ken's site is also a huge source of information on the HP history.

HP 200C One of the oldest showpieces of the collection

The 200A Evolution

Starting from the innovative concept of the 200A oscillator, many instruments have been built to fill in many gaps in the electronic industry of the 40s and 50s. New options added to the original circuit basis, have generated a complete signal sources product line to solve different measurements needs.

The first evolution was just an extension of the frequency range covered by the instrument. The 200C extended the first range down to 20 Hertz and added a fourth range to cover up to 200 KHz.

The HP 202D

Wider Frequency Range

The 200D covered from 7 Hz to 70 Khz in four overlapping ranges.

The 202D shown on the right lowers the first frequency range down to 2 Hz .

The dial of all these instruments is calibrated directly in cycles for the lowest range. A switch selects the range and indicates the power multiplying factor. The dial calibration of Models 200A, 200B and 200C covers approximately 180 degrees, with an equivalent scale length of about 60 inches.

Under normal conditions the frequency drift is less than +/- 2 % including initial warm-up. No zero setting is necessary on these oscillators.

The HP 200i tuning dial as shown in the 1945 catalog No 18A Oldest catalog in the collection

Better Accuracy

The front cover title of our oldest catalog No 18A dated 1945 is "LABORATORY INSTRUMENTS for Speed and Accuracy.

Accuracy was already the main guideline for new product development at HP.

Here is a picture of the 200i tuning dial as shown on page 7 of the 1945 catalog with the following comment:

"Main tuning dial of the 200i, which is an oscillator of the band-spead type, intended for comparison work. The dial is calibrated over approximately 300° with effective scale length about 90" and range of 6 cps to 6 Kc. Each Model 200i is carefully hand calibrated to insure maximum accuracy."

The HP 205AG

More Output Power & Multifunction

The 205AG brought the output level to 5 Watts into an external load of 50, 200, 500 or 5000 ohms with a distortion of less than 1 % from 20 cps to 20,000 cps.

Another innovation is that the 205AG integrates six basic instruments in the same box to make amplifier or network, loss / gain measurements.

As shown in the block diagram below the signal source is the model 200B basic circuitry followed by a 5 Watt (2 x 6L6 tubes), push-pull amplifier whose output is applied to the network under test through a 110 dB, 1 dB step attenuator and a line matching transformer. The control part of the 205AG integrates two vacuum tube voltmeters, one to measure the input and the second to measure the output of the device under test.

This is the first example of an HP product that provides answers to multiple problems found in production testing. Combining different tools in a single unit results in many advantages for instruments of this era where temperature drift and component aging were significant sources of measurement uncertainty.

HP 200CD

The 200A Upper Frequency Raise to 600 Kc

In 1952 Barney Oliver did a complete redesign of Bill's basic oscillator to raise the upper frequency limit to 600 Kc.. Barney was a classmate of Bill and Dave at Stanford, and was employed by Bell Telephone Labs. He was recruited to join HP in the late 1940s.

John Minck, in his "Inside HP Narrative" tells the story as follows: "Barney had a way of looking at problems that was unique. His first look at the circuit of the HP 200 convinced him that simply by going to a balanced circuit configuration, he could get well-over a 10 to 1 improvement in the frequency coverage. They tried it, and it worked, to 600 Kc, the first of hundreds of contributions that Barney would make to this Company, over a 40 year career."

The HP 200CD has the following specifications in the 1952 catalog page 9: Frequency coverage 5 cps to 600 Kc in 5 ranges. 160 mW into 600 ohms or 20 Volts open circuit at 1 % distortion and +/- 1 dB frequency response.

The HP200CD was a serious competitor in the HP longest product life contest. It remained in the Hewlett-Packard Test and Measurement catalog until 1985, a full 33 years which is rare in the electronics industry. Last, but not least, the 200CD was the last fully vacuum tube instrument produced by HP. The 428B Clip-on DC Milliammeter remained one more year in the catalog but for the purist, the 428B included some transistors in its latest versions.